Electronics Line iconnect Bedienungsanleitung

PentaInstallation, OperationInstallation, Operationand Programmingand ProgrammingELECTRONICS LINE’S TECHNICAL SUPPORT DEPARTMENTINTERNATIONAL: (972)-3

102.5: Mounting the KeypadUp to 3 LED keypads can be connected to the Penta control panel. To mount thekeypad:1. Separate the front and back cover of

114. Connect the keypad to the control panel according to the following diagram. 5. Reassemble the front and back cover of the keypad.2.6: Turning on

12CHAPTER THREE: SYSTEM OPERATION3.1: GeneralAll operation and programming of the Penta can be performed using any one of thethree LED keypads that ca

133.3: Command CodesCommands are executed by pressing the ‘Q‘ button followed by the correspondingcommand number and, in some cases, a valid user code

14Stay ArmingThis feature only arms perimeter zones. This allows the user to stay within theprotected area while the system is armed.To “Stay” arm the

153.7: User CodesThe Penta is capable of maintaining four user codes, a duress code and an installercode. Each of these codes are four digits long. Of

163.8: Zone Bypassing/UnbypassingThe Penta offers the user the ability to bypass zones. When a zone is bypassed, it isignored by the system and will n

173.10: Additional OperationsBell CancelTo cancel the bell:• Enter a valid user code or turn the keyswitch as if disarming the system.Bell/LED TestTo

18CHAPTER FOUR: PROGRAMMING4.1: GeneralThe Penta control panel may be programmed using either the LED keypad orElectronics Line’s Remote Programmer. I

194.3: Programming ParametersThe following section lists the Penta’s programming parameters which are used toconfigure the system. For a listing of th

2

20Address 03: Zone 1 DefinitionOne of five response types can be assigned to zone 1. Each zone type can beprogrammed as ‘Silent’ or ‘Audible’. A ‘Sile

21Address 10: PGM OptionsThe PGM (Programmable Output) can be used for indication of certain status or troubleconditions. When the PGM output is activ

22Address 26: [E] Key alarm restoreAddress 27: System Armed (User Code 1)Address 28: System Armed (User Code 2)Address 29: System Armed (User Code

23Telephone numbersAddress 54: Primary Telephone NumberThe primary telephone number is the first number that is dialed when an event occurs.A maximum

24APPENDIX A: HEXADECIMAL CONVERSION CHARTThe following is a decimal to hexadecimal conversion chart to be used as an aid inprogramming:Dec Hex Dec He

25APPENDIX B: GLOSSARY OF TERMS24hr Zone A zone which is always active regardless of whether the system is armedor disarmed. Opening a 24hr zone alway

26Distress Keys The three distress keys (F, E and P) generate different types of alarmwhen pressed and held down for two seconds.Duress Code Entering

27PPerimeter Zone Perimeter zones are armed during both regular and Stay arming and canbe defined with or without an exit delay.Periodic Test The peri

28INDEX24hr zone ...2024hr Zone...5AC Protection Fuse...

29Parameter Addresses ...18Parametersprogramming...19PartsList of...

3TABLE OF CONTENTSIntroduction... 4About the Pen

30ELECTRONICS LINE (E. L.) LTD. AND ITS SUBSIDIARIES - LIMITED WARRANTYELECTRONICS LINE (E. L.) LTD. AND ITS SUBSIDIARIES (EL) warrants its products t

Penta - Programming Worksheet (01) SYSTEM PARAMETERS____,____,____,____,____P and E Key FunctionP and E Audible Alarms - 0E Audible Alarm, P Silent Al

EVENT CODES(11) __,__ Alarm from Zone 1(12) __,__ Alarm from Zone 2(13) __,__ Alarm from Zone 3(14) __,__ Alarm from Zone 4(15) __,__ Tamper Alarm(16)

Penta – Default Values (01) SYSTEM PARAMETERS____,____,____,____,____P and E Key FunctionP and E Silent AlarmsKeypadsOne KeypadTamper Zone DefinitionT

4INTRODUCTIONAbout the Penta Installation, Operation and Programming ManualThis manual is designed to help you with the installation process for the P

51.2: ZonesThe Penta control panel includes four security zones plus one tamper zone which can bedefined for use with an ON/OFF keyswitch. The four se

6Central Station CommunicationThe Penta uses a standard 20pps 4/2 no parity protocol for central stationcommunication. All events can be programmed to

7CHAPTER TWO: INSTALLATION2.1: Parts and OptionsPenta Household Burglary Alarm Control Panel 1LED Keypad 12.2KΩ ¼W resistors56 x ¼ mounting screws 4Mo

2.3: Wiring DiagramZ4Z3Z2Z1ZONECONNECTIONSF2 F3AUX-+KPDK2 K1PROTECTION FUSES:F1 (BATT): 1.6A/250VF2 (AC): 1.6A/250VF3 (AUX): 1.0A/250VF4 (Bell): 1.0

9+3748596LOAD(100mA max.)AUXPGM2.4: Terminal Connections15-16.5Vac InputTerminals 1 & 2: Connect a 15-16.5Vac transformer rated at 22-30VA, using